Frequently Asked Question!
We’ve put together a list of the most frequently asked questions. If you have a question that is not listed here, please feel free to contact us.
Electrostatic is based on the principle that opposite charges attract and like charges repel. Two positively charged things will repel each other. Using this natural electrostatic phenomenon, Victory has developed a patented breakthrough cordless application technology.
The Victory Innovations Cordless Electrostatic System places a positive charge on the liquid before entering the nozzle allowing the maximum levels of liquid to be charged and sprayed at negatively charged surfaces (most surfaces are either negative or neutral) allowing for a more complete coverage of the targeted surface.
Using our patented technology, the process of positively charging the liquid starts at the charging ring and flows to the tank. This way all the liquid has a positive charge prior to reaching the nozzle. As most surfaces are either negative or neutral, the dispersed droplets spread out more evenly and seek out a negative or neutral surface.
The end result is that the liquid can be applied faster, using less liquid and achieving a more complete coverage of the surface.
Yes, Uk Eco Electrostatic sell the world’s No 1 Disinfectant.
Bright Water is the most innovative and cost effective product with a neutral pH and 100 % ecological for humans, food, animals, oceans, and plants.
Bright Water is a highly potent anti – microbial against all pathogenic microorganism and would eradicate any virus with any type of surfaces including COVID19 within seconds upon application.
Bright Water is fully compliant with HACCP ( Hazard Analysis and Critical Control Point) and an approved product by ECHA (European Chemicals Agency).
ONE YEAR WARRANTY
Uk Eco Electrostatic Ltd will repair or replace, without charge, any defects due to faulty materials or workmanship for one year from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information, email us at info@ukecoelectrostatic.com
This warranty does not apply to damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights, which vary in certain states or provinces.
a. After each use before storing or before switching chemicals, spray water through the machine for 20 seconds to rinse out the line of any leftover chemicals that may start to build up.
b. Do not transport or store chemicals in the tank while connected to the sprayer. If you want to store chemicals in the tank, we recommend you purchase a tank cap and seal up the tank during transporting and storage of the sprayer. If you do not empty the tank, the user runs the risk of the liquid spilling in the case and damaging the electrical board in the unit or in the battery.
c. A plugged nozzle can occur if the machine is not regularly rinsed. If you have a plugged nozzle, remove the nozzle, soak in hot, soapy water for 10 minutes, then blow out the nozzle with compressed air. Watch our video on cleaning and maintenance to see a demonstration.
TO ADJUST THE NOZZLE
- Remove the battery from the unit.
- Insert the nozzle wrench into the front end of the unit.
- Rotate wrench until the tabs on the nozzle and the slots on the wrench are lined up.
- When the wrench slots and the nozzle tabs are lined up, the wrench will be completely inserted into the front end, rotate the wrench clockwise to adjust to a different size spray. The largest particle tip has a line cut through it, rotate clockwise until you hear a click to get the medium particle and rotate clockwise again until it clicks again to get the smallest particle.
- Remove the wrench when complete.
TO REMOVE THE NOZZLE
- Remove the battery from the unit.
- Insert the nozzle wrench into the front of the unit.
- Rotate wrench until the tabs on the nozzle line up with the slots in the wrench.
- When the tabs and slots are lined up the wrench will be completely inserted into the front end.
- To remove, rotate the wrench in the counter clockwise direction until the nozzle comes loose (¼ rotation).
- Remove the wrench when complete.
TO INSERT THE NOZZLE
- Remove the battery from the unit.
- Insert the nozzle into the wrench, lining up the tabs on the nozzle and the slots on the wrench.
- Insert the wrench with nozzle into the front end of the unit.
- Push in and rotate the wrench ¼ turn counter clockwise. When you hear a click the nozzle is in position.
- Remove the wrench when complete.